I got interested in pocketknives when I was in university. I found that I was doing a lot more cutting than I did previous to that point in my life. Cutting open food-containers, cutting open boxes, slicing paper, cutting open wrappers and plastic packaging, cutting tags…all kinds of things. And I often found myself in a situation where I needed a pocketknife, but didn’t have one. And after this happened more than a couple of times, I decided that the time was right for me to actually go out and find a nice knife.

Well, that was about ten years ago, and since then, I’ve gained a minor appreciation for antique and vintage pocketknives. I wouldn’t say that I’m an active collector of pocketknives, but I know what I like, and I sometimes go hunting for them at flea-markets and antiques fairs, and if I see something nice for a good price, I buy it. Depending on how practical the knife is, or how interesting or different it is, I may either add it to my small collection, or sell it after I’ve finished tinkering with it.

That said, I don’t have a large collection of pocketknives. Maybe three or four small ones? I used to have loads more – at my max, about eight or nine, but I sold the vast majority of them simply because I tend to be a USER more than a COLLECTOR. I don’t like owning things that I don’t use, and so because of that I sold almost all of them, except ones which I really, really liked.

I have three little pen-knives with mother-of-pearl and ivory scales (if you’re a regular follower of this blog, you might remember I did a posting about a couple of those a few months back), and I used to have four or five others – which I gradually sold over time as I found better knives to replace them.

As of the writing of this particular post, I just sold another knife (a two-bladed English Barlow-pattern) online to trim down the collection a bit.

But that’s not what this posting is about. This posting is about the knife I found, which replaced that English Barlow!

…and there it is!

The German Stockman

I bought this knife about two weeks ago for a couple of tens of dollars. I don’t exactly blow the bank when it comes to buying pocketknives, and this is probably the most I’ve ever spent on a knife in my life! It’s a three-bladed slip-joint folding pocketknife, of a style known as the ‘stockman’, so-called because this design was originally meant for use by farmers, cowboys, drovers, shepherds and livestock managers. The three blades were meant to accomplish different tasks when it came to looking after livestock (I’ll get into that later on down the line…).

I liked the knife because it was a nice, medium-sized knife with blades of decent length and thickness, and it had the sort of simple, clean look that I generally go for in things that I like to use on an everyday basis. The three blades gave me options, and the black scales were elegant without being flashy.

How Do You Know it’s from Germany?

I’m not entirely sure what company made the knife, but it comes from Solingen, Germany. This much I do know, because it’s stamped on the shank of the blade. And as the ShamWow guy says: “You know the Germans always make good stuff!”

They sure do! After all, not for nothing has Solingen been the cutlery capital of Europe for the better part of…what? Five hundred, six hundred years? The cutlery trade in Solingen dates back, quite literally – to Medieval times.

They still make surgical blades, razors, scissors, kitchen-knives and cutlery and pocketknives there today! Famous companies like DOVO (straight razors), Wusthof (kitchen knives), and Boker (more razors), are all based in Solingen. The city was originally home to a famous guild of swordsmiths back in the Middle Ages. If you’re collecting antique straight-razors or pocketknives, you can generally rest assured that any knife with ‘SOLINGEN’ stamped onto the blade is worth the money spent to get it. After all – 700-odd years worth of knife-making has to count for something, right?

I don’t know how old the knife is, exactly, but my guess is that it’s from the early 20th century, most likely before WWII. That being the case, I doubt this knife is more than about 80 or 90 years old.

The Anatomy of a Pocketknife

The classic, slip-joint, folding pocketknife comes with about half a dozen different components. So  you can follow what I’m going to write later on in this post, here’s a breakdown…

The Blades

A knife obviously starts with the blade. Most slipjoint knives have at least two blades. Some only have one, most will have two or three. Some models made by other manufacturers (such as Victorinox in Switzerland) have knives which have loads of blades and accessories folded away. But for the basic knife, one, two, or three blades – sometimes four – is standard.

A slipjoint pocketknife will have blades that have ‘nail-nicks’ cut into them. These are the little grooves that run under the spine of the blade, so that you can actually pull the blade out of the knife-handle.

The Handle

The handle of the knife is made up of about four or five different components, they are…

The Bolsters

The bolsters are the end-pieces on the ends of the knife, usually made of nickel-silver, steel, or brass.

The Liners

The liners are flat strips of metal inside the knife. They’re usually made of brass, to prevent rusting. The liners serve as washers to reduce friction between the moving parts of the knife. There is a liner between each blade, and the exterior of the knife.

The Back-Spring

The spring is the flat, flexible steel lever or leaf-spring on the knife that holds the blades open, or shut. It flexes up and down as the blades are opened and closed. The tension on this spring is what stops the blades from flopping around.

The Pins/Rivets

Knives have pins or rivets punched through them. These are here to serve as pivots or hinges for the blades, and to hold the handle components (spring, liners, blades etc) together.

The Scales

Last but not least, you have the scales. Not all pocketknives have scales. Some do, some don’t. Their purpose is to protect the liners and the rivets and other components of the knife from damage, although these days, scales are largely there for decorative purposes. Scales can be made from almost anything – celluloid, wood, bone, ivory, mother-of-pearl, tortoise-shell, and even solid silver…are very common on antique and vintage knives.

Different Knife Models

Pocketknives come in various styles and types. While these days there are loads of different variations – when you’re looking at vintage and antique knives, you’ll largely come across a set group of basic designs, although these are by NO MEANS the only types out there, and there are countless variations. Here are just three or four of the really common ones…

The Stockman.

The stockman is the knife-type which I’m building this posting about. Used by livestock cowboys, farmers and shepherds in the past – hence the name. The stockman is a three-blade folding knife, typically consisting of a clip, sheepsfoot, and spey blade. They range in size from a couple of inches to four or five inches long (the one I have is four inches, closed up).

The Barlow

One of the OLDEST knives around, the ‘Barlow’ style pocket-knife has two blades at one end, one long all-purpose blade, and one shorter blade, usually for cutting pen-points for quills, and sharpening pencils. Barlows go back for CENTURIES and their use is dated all the way back to the 1600s.

The Trapper!

The trapper knife comes from the knives originally used by fur-trappers back in the 1700s and 1800s. Trapper knives have two blades on one end of the handle, and the blades are long and equal-length, used for killing and skinning animals for their fur pelts.

The Canoe.

The canoe-knife is exactly what it sounds like – a knife shaped like a canoe! It’s a smaller knife, with two blades, one on each end of the handle. The body of the knife is cigar-shaped, but with a dip in the middle on one side, and curved edges at the ends, giving it the general appearance of an American Indian canoe, hence the name.

There are loads of other knife-styles out there, but these are four of the most common ones that you’re likely to find at flea-markets, antiques shops, auction-houses, etc.

Restoring Your Pocket Knife!

Keep in mind that not ALL knives can be restored. Some can, some can’t. Some are just too far gone, too broken, rusted or damaged to be repaired or revived. Here, I’ll be walking you through what I do to all the knives that I’ve ever bought, fixed and sold, or kept and used.

If you have the tools and equipment, you can literally pull a knife to pieces and clean it that way, but I’m working with the assumption that you, like me, probably don’t have most of those things, and that you’ll be cleaning and restoring your knife WITHOUT pulling it apart. Based on that assumption, let’s begin!

So, you found a really sweet pocketknife at the flea-market, or in an antiques shop, that you really love! It’s just the right size, or perhaps it’s the style or shape, or the scale-material, or maybe it’s manufactured by the same folks who made the one that grandpa gave you…which you lost as a teenager…However it happens, you found a knife! Only…it’s not in the best condition. It’s not completely dead, but it’s a bit rusty, it’s really stiff and crudded up, and it couldn’t slice melted butter. So, what do you do?

Rust-Removal.

For me, the first step is always rust removal. To do this, you need sandpaper. Get fine or ultrafine sandpaper, and a lubricant (Brasso, or sewing machine oil are generally good). Rub the lubricant over the rusty areas (usually the blades, hilts and back-springs) and start rubbing the sandpaper over it. Start coarse, and work to fine, then ultrafine. If you want to, you can also use 0000-grade ultrafine steel wool for the really soft, last cleaning. The aim is to remove the rust, and polish the blade at the same time.

If the back-springs on the knife are really rusty, then if it’s on the outside – just run the knife back and forth across your chosen polishing-abrasive to remove the rust, with oil as a lubricant. If it’s INSIDE, then you can use a popsicle stick with some really fine steel wool, or sandpaper, to try and sand out the rust on the inside of the spring between the brass liners.

This should remove most of the surface-rust on your knife, while also polishing the blade. Keep in mind that almost all antique pocketknives have CARBON STEEL BLADES. These things rust if you even sneeze at them wrong, so having restored the shine on the blade, or at least, having removed the rust – keep the blades DRY when not in use, to prevent rusting, and clean them immediately after any use involving moisture. A single drop of water is all it takes to get rust growing on these antique blades.

Cleaning Out the Guts!

Antique knives are often CLOGGED with crud! Dust, grit, pocket-lint, hair and all other kinds of CRAP usually ends up jammed up inside these things. To clean it out, open the knife entirely, and using a needle, pin, or other suitable long, thin, sharp object – clean out the grooves and gullies between the washers, the springs and the blades. This can take a while.

Cleaning under the Scales.

On the vast majority of antique pocket-knives, scales are simply riveted or pinned onto the outside of the knife and are largely decorative in purpose. But that’s no reason why they shouldn’t look nice! Loads of gunk and crud can EASILY get BEHIND the scales, between the back of the scales, and the brass liners that make the body of the knife-handle. One way to clean this crud out is to use a pin or needle.

Only do this if you can actually get the needle into the gap between the liner and the scales. If you can, simply stick the needle in and wiggle it around from side to side, up and down, back and forth. This will scrape up all the crap that’s accumulated inside there over the course of DECADES, and sweep it out when you remove the needle.

Don’t be afraid if the scales suddenly POP UP! or even worse – drop off! This is nothing to be worried about. If the scales DO fall off, simply clean them (and the liners) as best as you can (either with tissues, water, oil, or a polishing compound) and them simply pop them back on, over the same rivets that held them in, in the first place. You may need to tap the scales back on to pop them back into place. If the scales are loose – apply some glue to them (or the liners) before reattaching the scales, then simply apply pressure to ensure proper adhesion, wiping away any glue that pops out the sides.

Voila! Nice, clean scales.

Lubricating and Cleaning the Pivots and Springs

When it comes to cleaning and restoring antique or vintage folding pocketknives, this is, almost without a doubt, the one part of the restoration that can take ages. Hours. Days. Even WEEKS, if you want to do it properly!

Loads of gunk builds up inside these knives, just from decades of use, and dust and crud and lint and grime getting into the mechanisms. This can make the knives very, very, VERY stiff. This makes them hard to open, hard to close, the blades pull on your fingernails, they’re painful to use, and even worse – you could CUT yourself if the knife suddenly springs open when you’re fighting with it!

So, how to fix this?

To do this, you’ll need three or four things:

• A bottle of sewing machine oil (you could use WD-40 as well, but you’ll be using a LOT of lubricant, and WD-40 STINKS after long use, so…it’s not my first choice…)
• Fine and Ultrafine Sandpaper.
• Loads of tissue paper or toilet paper, or paper-towels.
• Cotton-buds/Q-Tips.
• A needle or pin (optional).

So long as it’s not physically broken or damaged in some way, the main reason why the blades on your folding, antique pocketknife jam, jar and won’t open or close smoothly, is because the knife is DIRTY. REALLY, REALLY, REALLY DIRTY. To have a knife that opens and closes smoothly – this DIRT needs to be REMOVED. Dirt causes FRICTION. That’s why your damn knife ain’t workin’ properly! Capiche?

“Can’t you just…I dunno…LUBRICATE IT with OIL?”

…Yeah. But what happens when the oil dries up? You’re right back to square one. To do it properly, the gunk has to be REMOVED.

“Yeah but I don’t have any way of pulling the knife apart. How do I remove this stuff?”

Fear not, young grasshopper!

What you’re gonna do is flood the knife with oil. Then, once the knife pivots and springs are full of oil, you’re going to open and close the blades several times. This wiggling and movement spreads the oil around inside the knife, inside the pivots and springs and hinges, between the blades and liners. It also dislodges any of the crud and gunk trapped inside.

Once you’ve done that – get a paper towel or tissues or whatever – folded up a couple of times, to make an absorbent pad. Place it on a flat surface like a tabletop.

Now, put the knife, spring-side DOWN (blades facing upwards), on top of the paper. Applying as much pressure as you can – rub the knife HARD, back and forth lengthwise across the tissue-paper.

I’ll pause here for a minute, while you recoil in disgust, at the black, oily, gunky brown crud that comes seeping out of your knife…

See all that stuff? That’s what’s inside your knife. That’s the grunk you’re trying to get rid of. That is the stuff that’s causing your knife to jam. Remember that the oil is transparent – so anything that comes out of the knife that is NOT transparent – is grime that’s causing the knife to jam.

Repeat this process as often as you must, until the oil that seeps out onto the tissue-paper is clear and transparent (or as close to transparent as you can get it). That means that the crud between the springs and pivots has finally been removed.

If you have an ultrasonic cleaner – pop the knife in there every now and then, to flush out even MORE gunk. Just remember to DRY it really well once you fish it out of the water.

Finally – you can use sandpaper to sand down the shanks and springs when they’re exposed, to remove any surface-rust or grime, to improve the action of the knife.

To achieve results this way, it can take days, even weeks, before all the crud is removed, but once it is, your knife will open and shut as smoothly as if it were new. No more stopping, jerking, tugging, breaking finger-nails, or risking slicing your fingers off, when opening your knives, ever again! If you haven’t achieved the results you want, that means that the knife is, in all likelihood, still clogged with grime. Keep going and don’t give up on it!

Also, it’s good to repeat this process every now and then (like every few months, if you use the knife regularly) to stop gunk from building up and jamming the blades again. Finally, once the knife is opening and closing nice and smoothly, lubricate the pivots and springs with one last drop of oil, and wipe it down to clean it.

Sharpening the Blades

The final step in restoring your antique or vintage knife, is sharpening the blades! For this, you’ll need a bucket of water, two or three high-quality sharpening stones, a sink, and a towel or tissue-paper. I always recommend leaving the sharpening of your knife to the VERY END. This prevents accidental cuts during the polishing, rust-removal and lubrication stages.

Soak your sharpening stones in your bucket of water for as long as possible (overnight or longer is best) until they’re nice and wet and have soaked up the water (high quality stones are often quite porous). Then rest them on a flat surface (kitchen counter or similar) and start sharpening.

Open one blade at a time, from your knife, and rest it on the flat surface of the stone, raised slightly on the spine, and so that the edge of the blade just kisses the stone. Slide the blade back and forth along the stone, in a wide, oval or figure-eight pattern, adjusting the angle and position of the blade as you go, to sharpen its entire length, including any curves in the blade. Do this as fast as you can without damaging the blade, at least twenty times. Flip the blade over and repeat the process on the other side. If done properly, the blade will slide smoothly along the stone. If it jars or scrapes, then you’ve got the wrong angle!

Once you’ve done twenty or more strokes for each side, remove the blade, wash or wipe it down with the tissues or towel, and then start on the next blade. It can take a while to sharpen a blade successfully (especially if it’s curved) but patience will yield results!

Closing Remarks

Anyway, that just about does it for me. Hopefully these instructions were useful to you in reviving that old pocketknife you found lying around somewhere, and has restored it to being a useful tool yet again! Tinkering with stuff like this is lots of fun and it stops otherwise useful things from being discarded and tossed out. Which in the case of this knife, would’ve been a real shame…